[Sep 20, 2021] NS0-194 Ultimate Study Guide - PassTorrent
Ultimate Guide to Prepare NS0-194 Certification Exam for Network Appliance NCSE in 2021
NEW QUESTION 28
A customer is showing disk utilization is at 100% in Active IQ even though there are low protocol operations on the controller. You review the data shown in the exhibit.
In this situation, what should you do?
- A. Reseat shelf module B.
- B. Add disks to the aggregate to bring down the average utilization.
- C. Replace disks 6b.34 and 6a.19.
- D. Replace disk 6b.39.
Answer: D
NEW QUESTION 29
You are working on a fabric MetroCluster. After a site failure, the plex starts to resync automatically to the aggregate mirror of Aggr1. The plex now shows a status of resyncing. During this process, you experience a slow resync of the SyncMirror plex.
In this scenario, how do you solve the problem?
- A. Tune the resync speed by adding a QoS policy and limit the concurrent I/O to the aggregate.
- B. Destroy and re-create plex, then run a baseline sync.
- C. Tune the resync speed using the storage raid-options command.
- D. Add more disks to the aggregate to add more I/O capacity.
Answer: A
NEW QUESTION 30
You just set up a new clustered Data ONTAP 8.3 environment and want to monitor volume performance.
Which two commands or products would help you accomplish this task? (Choose two.)
- A. Quality of Service (QoS) commands
- B. Syslog Serve
- C. OnCommand Performance Manager
- D. OnCommand System Manager
Answer: B,D
NEW QUESTION 31
You have a 6-node cluster with six identical controllers. You are upgrading from clustered Data ONTAP 8.3.1 to clustered Data ONTAP 8.3.2.
From the Upgrade Advisor, you downloaded the upgrade plan. In this scenario, which two steps are part of that plan? (Choose two.)
- A. Set a new image as the default image.
- B. Verify system health.
- C. Migrate all aggregates to the HA pair that was most recently upgraded.
- D. Perform LIF migration of all SAN LIFs before takeover.
Answer: A,D
NEW QUESTION 32
Which NetApp technology enables you to perform block-based replication from NetApp Element software to Cloud Volumes ONTAP?
- A. MetroCluster
- B. SyncMirror
- C. Cloud Sync
- D. SnapMirror
Answer: D
NEW QUESTION 33
You receive the error shown below on a FAS2750 HA pair.
Mon Jun 24 00:27:30 UTC [NetappA: scsi_cmdblk_strthr_admin:
scsi.cmd.checkCondition:error]: Unknown device 0a.00.99: Check Condition: CDB
0x12: Sense Data SCSI:hardware error - (0x4 - 0x44 0x0 0x0) (0).
The system is cabled as shown in the exhibit.
What should you do to clear the error?
- A. Replace the controller of controller A.
- B. Replace the cable connected to controller A's 0a port.
- C. Re-cable the system per the FAS2750 installation guide.
- D. Replace the controller of controller B.
Answer: A
NEW QUESTION 34
You provision a new ONTAP volume to use as a VMware vSphere NFS datastore. You successfully mount the volume to the vSphere (ESXi) hosts, and you can read, write, and delete small (less than 1 KB) test files.
However, you cannot upload large files or Storage vMotion VMs to the new datastore. You verify that the volume is reporting adequate free space.
Which action should you perform to troubleshoot this problem?
- A. Verifythat the NFS LIF is on its home port.
- B. Verify that the security style is set correctly on the volume.
- C. Verify the MTU configuration along the network path.
- D. Verify that the export policy is correct for the volume.
Answer: C
NEW QUESTION 35 
Referring to the exhibit, the UNIX user "prof1" will be looked up in which source first?
- A. nis
- B. dns
- C. ldap
- D. files
Answer: B
NEW QUESTION 36
You want to monitor and generate reports on a customer's IT infrastructure, including virtual and cloud-based components, even though the customer has not purchased or installed any ONTAP software.
In this scenario, which NetApp tool would be used to accomplish this task?
- A. OnCommand System Manager
- B. OnCommand Workflow Automation
- C. OnCommand Unified Manager
- D. OnCommand Insight
Answer: D
NEW QUESTION 37
After a storage administrator turned off IP fast path, all the NFS clients lost connectivity to the storage controller.
Which statement describes what happened in this scenario?
- A. The NFS clients are using NFS over UDP.
- B. The ARP cache Ss flushed when IP fast path disabled.
- C. No default gateway is configured.
- D. All clients are in the local broadcast domain.
Answer: A
NEW QUESTION 38
A user on an NFSv4 client is listing a directory and sees the file in an is -1 listing shown below:
"rwr------1 nobody nobody 10767 Mar 24 2016 party.txt"
The customer would like to know why the user and group shows as "nobody".
Which statement would explain why this is happening?
- A. The file resides on an NTFS style volume.
- B. The permissions does not allow for listing the owner.
- C. There is an NFSv4 ID domain mismatch.
- D. There is no owner or group set on the file.
Answer: B
NEW QUESTION 39
A customer asks what is the correct way to configure an ONTAP system for multi-tenancy. The customer wants to serve data and also protect data using SnapMirror from tenant A using network A and from tenant B using network B.
In this scenario, which statement is correct?
- A. This setup can only work if tenant A and tenant B use a shared network infrastructure.
- B. The customer must use different VLANs for the two tenants.
- C. The customer must set up two different IPspaces for the two tenants.
- D. Each node can only communicate with tenant A or tenant B, but not with both at the same time.
Answer: A
NEW QUESTION 40
Exhibit:
Your customer has recently migrated from their FAS3140 system running Data ONTAP 7.3.7 to a FAS2552 system running Data ONTAP 8.2.3 7-Mode through the head upgrade process.
They are no longer receiving the weekly AutoSupport notifications and want to know why. The exhibit shows the AutoSupport options from the nodes that have the same settings.
In this scenario, which solution is correct?
- A. In Data ONTAP 8.2, the protocol for AutoSupport is changed to HTTPS by default, so the customer must have an HTTPS destination for the AutoSupport data.
- B. In Data ONTAP 8.2, weekly AutoSupport notifications are no longer sent to all recipients to reduce the mail load. The customer should add their e-mail address to the autosupport. partner. to option.
- C. In Data ONTAP 8.2, weekly AutoSupport notifications are no longer sent to the autosupport.to recipient, but only to autosupport.partner.to and to autosupport.support.to. The customer needs to add their e-mail address to one of these options.
- D. There is no reason on the FAS2552 side why the customer should not receive the AutoSupport notifications. They should investigate their mail server to troubleshoot this issue.
Answer: C
NEW QUESTION 41
A customer has reported an unexplained reboot of an ONTAP node that did not generate a panic string or a core file.
In this scenario, which two sets of logs do you collect to further diagnosis the issue? (Choose two.)
- A. system core
- B. events all
- C. sp status -d
- D. sp status
Answer: A,B
NEW QUESTION 42
Test user "LAB\tester" can perform an operation in the CIFS share "HR" from the SVM "svm1". However, the rest of the users from the HR department cannot perform the same operation. You want to determine why only
"LAB\tester" can perform the operation.
In this scenario, which security trace filter accomplishes this task?
- A. vserver security trace filter create -vserver svm1 -index 1 -protocol cifs - windows- name LAB\tester
-trace-allow yes - B. vserver security trace filter create -vserver svm1 -index 1 -protocol nfs - unix-name tester -trace-allow yes
- C. vserver security trace filter create -vserver svm1 -index 1 -protocol nfs - unix-name tester -trace-allow no
- D. vserver security trace filter create -vserver svm1 -index 1 -protocol cifs - windows- name LAB\tester
-trace-allow no
Answer: A
NEW QUESTION 43
......
Network Appliance NCSE Fundamentals-NS0-194 Exam-Practice-Dumps: https://www.passtorrent.com/NS0-194-latest-torrent.html
Use Real NS0-194 Dumps - Network Appliance Correct Answers: https://drive.google.com/open?id=1jhziYBXuUHd_d832TKWpW3yaKnM7JJuW